Techno Vector 6202 – 3D

R179,025.00 EX VAT

TechnoVector 6
3D Wheel Aligner With No Limits!

TechnoVector 6 FREE MOTION wheel aligner has been designed to take measurements and perform alignments on steerable and unsteerable wheels in automotive companies, car service stations, automobile manufacturing plants, and diagnostic centers.

** Excludes lift.

Categories: , , SKU: TV6202M
Brands:Techno Vector

Description

Restrictions to existing 3D wheel aligners

It is common knowledge that when installing any 3D wheel aligner there are some restrictions on the distance to the front wall. Because of this a 3D wheel aligner installation sometimes becomes impossible.

TechnoVector Group’s new product TechnoVector 6 – has been designed to remove these restrictions and allow owners of small workshops to use 3D technology!

Operating principle

The camera sees measurement targets located on the front wheels and reference targets simultaneously. Camera and target coordinates in space are calculated. These data are used to calculate wheel alignment angles.

As all the measurement system is within the sizes of the lift and is raised and lowered together with the vehicle, adjustment can be performed at any height; posts of the lift do not overlap camera vision range.

Wheel aligner installation

TechnoVector 6 does not require assembly work. The wheel aligner is not attached to a certain lift or a workplace. It is enough just to move the shaft with reference targets, measurement targets and portable camera units – and your wheel aligner is ready to work at a new place.

Disc runout compensation

Disc runout compensation can be performed by rolling the vehicle. It is enough to roll the vehicle by ~ 40cm to perform this procedure.

Techno Vectro 6 wheel aligner is ideal for both big car service centers and small garages that want to use up-to-date 3D wheel aligners even in a small workshop.

Wheel alignment systems include the following basic parts:

  1. Computer cabinet
    • ergonomic operating control panel;
    • full-size keyboard;
    • wireless remote control;
    • up-to-date high-speed processor;
    • color widescreen monitor;
    • color inkjet printer;
    • TechnoVector 3D software.
  2. Self-centering wheel adapters.
    Self-centering wheel adapters fit a various range of wheel discs from 12″ to 24″ and are compatible with motor car and light truck discs.
  3. Measurement targets.Target boards covered with reflective sheeting do not contain electronic elements and consist of:
    • High-precision image targets. Images are covered with a protective oil-and-petrol resistant layer;
    • Durable impact-resistant housing.
  4. Shaft with reference targets.Shaft with target boards covered with reflective sheeting that do not contain electronic elements. It includes:
    • Shaft to fasten targets;
    • High-precision image targets. Images are covered with a protective oil-and-petrol resistant layer;
    • Durable impact-resistant housing.
  5. Portable camera units.
    HD video cameras allow a quick and reliable determination of target position in space and information transfer to PC over Wi-Fi.
  6. Vector 3D softwareMicrosoft Windows is used as a licensed operating system.
    The three-dimensional program interface allows you to see position and wheel alignment angles on the screen in real time.
    The user-friendly interface and advanced Help and Support System allow even novices to learn how to use the wheel aligner quickly and start working.
    The most up-to-date mathematical algorithms used in the software allow for the slightest image distortions made by the optical system.
    The software includes the advanced report control system.
  7. Accessories package.

Key features

Number of cameras2 stationary cameras
Camera type5 MPix machine vision industrial cameras, RAW
Mounting typeFloor-mount. T-shaped pillar
Cabinet typeV-series
ApplicabilityLift or Pit
Distance from cameras to the center of front turn tables1500-2500mm, recommended distance 2200mm
Main advantages
  • 2-camera configuration is sufficient to organize a wheel alignment post on any pit;
  • Set of 5Mpix cameras allows a better use of the aligner on the lift*;
  • Does not need calibration and allows you to start working right after installation**.

Installation Diagram

Installation Diagram

TechnoVector 6 has been designed to remove the limits when using 3D wheel aligners with lifts and in small workshops:

  • limits on the distance between posts of the lift;
  • limits on the distance to the front wall.

TechnoVector 6 can also be successfully used on the pit!

Diagrams of TechnoVector 6 installation variants on the lift and on the pit are given below.

Installation on the lift

When installing on the lift, the shaft with reference targets should be placed on the platforms of the lift in front, at a distance of 250-650mm from the axis of the front vehicle wheel and should be raised and lowered together with the vehicle.

ustanovka_tv6_05.png

! This installation variant does not require wheel aligner assembly and camera calibration.

 

Installation on the pit

Preparing a new workplace (pit) for TechnoVector 6

To install TechnoVector 6 on the pit, it is necessary to take into account the position of technological recesses for reference targets when you design the pit.

 

ustanovka_tv6_04.png

ustanovka_tv6_01.png

! This installation variant does not require wheel aligner assembly and camera calibration.

 

TechnoVector 6 installation on the existing workplace (pit)

Variant 1 (posts with reference targets)

If it is impossible to make technological recesses, reference targets can be placed in posts.

Posts with reference targets installed in them should be mounted at a distance of ~700mm from the front axis of the vehicle wheel.

ustanovka_tv6_03.png

! This installation variant requires post assembly and reference target correspondence calibration.

The assembly should be performed by a technician from the service center which is authorized to install TechnoVector 6 and 7 and to carry out start-up and adjustment.

Variant 2 (Mounting the shaft with reference targets on the wall)

If there is a main wall in front of the pit, the shaft with reference targets can be mounted on the wall with brackets.

The distance from the front vehicle axis to the wall should not exceed 2m.

The height at which the shaft should be mounted depends on the distance to the wall and can be within 960-1260mm.

ustanovka_tv6_02.png

This installation variant allows the customer to mount the brackets on the wall; the requirements to the height, distance from the wall to the axis of the front wheel and horizontality of the shaft should be taken into account.
Camera calibration is not required.

Please specify the installation variant, when you order TechnoVector 6 wheel aligners.

Tech Specs

ParameterMeasurement RangeMaximum
error in measurement		Average
error in measurement
Front Wheel Alignment
Camber±8º±3′±2′
Front Total Toe±5º±3′±2′
Caster±19º±8′±5′
SAI/KPI±19º±8′±5′
Lock Angle±45º±10′±5′
Rear Wheel Alignment
Camber±8º±3′±2′
Rear Total Toe±5º±3′±2′
Rear Individual Toe±2,5º±3′±2′
Symmetry Angles
Front Set Back±2,5º±3′±2′
Rear Set Back±2,5º±3′±2′
Thrust Angle±2,5º±3′±2′
Geometrical Driving Axis±2,5º±3′±2′

 

ParameterValue
Voltage, W220 ± 10%
Frequency, Hz50/60
Wheel Adapter (clamping arm) Mounting Range, in.12 ÷  24
Operating Temperature, °С+10 ÷ +35
Power Consumption350
Net Weight, kg280
Gross Weight, kg390
Volume, m31,7
Number of Packages7
Climatic category of the Device according to GOST (All-Union State Standard)GOST 15150-69

3D Software Features

3D Visualization

  • Compensation screen

  • The software features an animated 3D model of a generic car chassisThe wheels are positioned according to measured values of toe, camber and casterThe adjustment mode features several views: for each wheel, for each axle, general view, geometry view and a 2D mode3D gauges are displayed on the screen during the adjustment. They allow a better visualization of measured wheel alignment values

    All the information on the screen is updated live in 3D

    Print-outs generated by the software can also include 3D rendered images illustrating positions of wheels before and after the adjustment

Cutting edge technology

  • Adjustment screen – Main view

  • Extremely fast refresh rate of the measured values. Cameras can shoot up to 40 frames per second and the software keeps up with themDetects partially occluded targets*Multiple pass target detection allows working at extremely bright workspacesMultithreaded architecture utilizes all the capabilities of modern multi-core processors

    DPI-independent software scales correctly on every modern display including 4K monitors**

    Fast transition time. All the screens are preloaded at the start to ensure that there are no pauses while navigating.

    Extensive car model database is also preloaded right when the software starts and provides instant response time when searching or navigating

Measurements

  • Measurement screen

  • The software employs all the modern techniques to improve the precision of calculating targets positions in 3-dimensional spaceMultiframe smoothing reduces data instability due to vibrations, lighting conditions, yet swiftly reacts to any bigger changesThe software can automatically detect lift movement during adjustment and correct the live values if the lift skews at the adjustment heightTwo measurement coordinate systems are supported: calibrated horizon and vehicle plane*

    Hanging wheels mode allows adjusting car parameters with wheels jacked or turned to ease the adjustment.

    * Horizon measurement is unavailable on non-stationary wheel aligners

EASY AND CUSTOMIZABLE WORKFLOW

  • Adjustment screen – 2D view

  • Intuitive workflow that utilizes only four buttons at the bottom of the screenHelpful images are shown to remind the aligner technician of actions that need to be performedThe software stores all orders and all measurements. They can be reviewed at any time.The software stores history of all calibrations. The results can be reviewed at any time.

    All the navigation through most of the software can be done using hotkeys on remote control or the keyboard

    Web-camera support allows to display web-camera feed in main menu to help the driver to position the vehicle on the workplace.

    Multiple settings allow to fine tune the behaviour of the softwares interface. Possible options include:

    Print-out setup allows to select one of two templates and to set up texts and logos as well as several other useful options

    Automatic transitions are available where possible. For example, the software automatically detects when the compensation starts and proceeds to the next step.

    The user can select default modes for compensation, measurement or adjustment

    Several other fine-tuning for adjustment, compensation and measurement modes

DATABASE

  • Model selection screen

  • Contains more than 40000 vehiclesVehicle entries contain information, images and videos on identification and preparatory procedures and on how to adjust camber, toe and other valuesFree database updatesAllows to add an unlimited amount of custom models and to export/import them (especially good for brand-new car models and for markets with local car manufacturers not yet present in our database)

OTHER FEATURES

  • Report screen

  • Statistics screen displays valuable information about wheel aligners productivity: how many adjustment were made over a given period, what was the average adjustment time, etc.Tire pressure tables are available for most of the models in the databaseEasily export order data to Excel or other e-table software with ‘Export to CSV’ function ASA Network support.The TechnoVector 3D software works with Windows 7, Windows 8 and Windows 10.

Video

PDF

Techno Vector 6

Related products